Sewing to the Moon

View Original

DIY Easy Sewing Machine Cover

Is your sewing machine looking a tad boring? If it's a newer sewing machine, the answer is probably yes. The newer ones lack style and color. If it's a vintage machine, the answer is probably no. It's already gorgeous and full of vintage flair! Either way, let's add some new life to your machine with a dust cover. They're easy to sew and you can make one for all of your machines.

Back in the early pandemic days, mask-making was a big thing in this house and my husband bought himself a Singer machine. I'm a Brother fan through and through but, he liked the Singer's grey color. Of course, it's been sitting for over a year, untouched, and needs a little makeover. It's going to get a new fabric cover!

Let's make an easy sewing machine cover. You'll learn how to get the measurements and sew one up in an hour. Covers add fun to your sewing space and they keep your machine protected as well. Dust be gone! Speaking of dust begone, we just changed our AC filters. YIKES! They were long overdue. This is a friendly reminder to change your filters if you have an AC. ;) Go now, I'll wait. 

Supply List

  • 1/2 yard of fabric. Cotton, vinyl, canvas, denim, use whatever you want here.

  • Matching thread

  • Sewing notions: scissors, a marking tool, pins, etc.

  • Ruler

  • Serger for raw edges, or use a zigzag stitch if your machine has it

  • Sewing machine

Grab some paper, a pen, and a ruler. You can use a tape measure but, the hard ruler makes it a little easier to get an exact measurement. 

​Measure all the sides of your machine. 

Time for Math, (insert tears here).

Now it's time for some math. I don't do math so, hopefully, I explain this correctly. 

You'll be using a 1/2" seam allowance. So, you'll add 1" to each measurement number. (Each seam takes half of that inch.)

My machine is 12" tall by 15" wide. So, I'll add 1" to both of the measurements. 
12 + 1 = 13.  15 + 1 = 16. So, my final rectangle will be 13x16. But, we're not done yet.

Next, you'll add 2" to your height. This will allow the front and back to "roll over" the top.
The new measurement will be 14x16. These will be my front and back pieces. Cut 2.
* If your machine is extra deep, you may need to add more than 2" to the top height. 

The sides will need 1" added to your measurements.
My side measurements are 6.5" by 4". Add 1" to each and they'll be 7.5" by 5". *If your top is narrower than your bottom, use your ruler to connect the top and bottom lines to form a trapezoid (a pyramid with the top cut off). Cut 2 mirrored. There might be a left and right side due to the angles. ;)

I hope I explained this correctly. Math is not my strong suit, so send me a message or leave a comment if you need help. I'll try my best to help, but no promises. ;) LOL Others might offer help in the comment section too. 


Bonus tip

Cut out your 4 fabric pieces. You should have 2 sides and 2 front/back pieces.
This is where you can have fun and make it your own. Cut out four different colored fabrics or use different fabrics for the sides. You could piece together different fabrics to make a quilted look, or add some embroidery to the front. The possibilities are endless. 

OPTIONAL:
If you do add embroidery or make a quilted one, you might want to line yours.
In this case, sew 2 covers the same size, pin right sides together, and sew along the bottom edge, leaving a 3" gap for turning out. Top stitch the bottom to close the gap and you'll have the embroidery stitches/quilting seams enclosed.

Using the rotary cutter and mat for the rectangles.

Sewing Time

  • Start by serging or zigzagging along the top edge of the front and back pieces only.

  • Fold the serged edge down 1/2", then press. Topstitch 1/4" away from the edge. You're going to create a slit opening for your handle. *You can skip this part if you want. But, it's nice to have access to the handle when taking the machine to the repair shop or moving it to another spot in your sewing space. 


​Place both pieces RST (right sides together) and pin 2-3" from the sides, leaving the middle unpinned. You may need to adjust this measurement according to your machine. Sew from the side edge to the pins, only. Don't forget to backstitch.

The middle will be left open for the handle to pop out of.

Take a side piece, and fold it in half to find the center top. Make a little snip or mark with a pen. Do the same to the other side piece. 

Next, pin the side piece to one front/back Right sides together, by starting at the top. Put a few pins at the top, then go down to the bottom and start pinning upwards from there. This ensures your hem matches up. Next, you'll want to ease the curve of your corners. This may get wonky but, pin as well as you can. It doesn't need to be perfect.

​Sew, using a 1/2" seam allowance. 

It may be helpful to sew from one end upwards as far as you can go. Then, sew from the other end up and around the curve.  Puckers might happen, but this way felt easier to me. 

After one side is sewn, try it on the machine. Check the fit. Is it too long? Will the other side fit properly? Does it hang like a baggy bag? If there are any issues, fix them now.

  • If it's too big, make the seam allowance larger. (Use 3/4"-1")

  • If it's too small, unpick it and make the seam allowance smaller. (Use 1/4" instead)

  • If it's too long, trim away the excess or make a deeper hem. (Make a 1" hem)


​Luckily the sewing Gods were on my side and I was fortunate for mine to fit perfectly. Yay, math was on my side, for once. 

If it fits perfectly, move on to pin and sew the other side piece. Go about it the same way you did with the last side piece. After it's sewn, give the seams a good press. Slip it over your machine and admire it for a few seconds. 

You're almost done. The hem is all that's left to do.

Serge or zigzag around the bottom edge. Fold up 1/2" and press. Topstitch and you're done. 


If the bottom is too short because math is hard, just add a strip of ribbon or pom pom trim. It'll look like you did it on purpose. ;)

Easiest hem ever, serged edge and folded over once.

My husbands sewing machine will be dust free now.

Hole for the carrying handle.

Ta-da! Now go give your sewing machine some flair and keep it dust-free. 

If you make one for your machine, tag me on Instagram @sewingtothemoon. I'd love to see what you create. Now, I am off to sew a new cover for my serger.

Happy sewing,
​Annette